Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterTrack Realignment in Whitney, NV
Track realignment is the process of bringing a garage door’s vertical and horizontal tracks back into true so the door travels evenly instead of binding, skipping, or hanging on one side. In Whitney, a door that’s been knocked out of alignment usually announces itself with a grinding scrape or a gap at one corner, and it gets worse every cycle until the rollers or the opener pay for it. Servo Garage Doors Whitney handles track realignment as a standalone repair, quoting a flat written price before anything is touched and handing you a photo record of the bent steel when we leave. Call (888) 402-1096 and a live person answers, day or night.
This page sits under our broader Garage Door Repair service, because track work is one of the most common reasons a door stops behaving. It’s also one of the most misdiagnosed. Homeowners in Whitney are often told they need a new door when what they actually need is forty minutes with a level and a track-bending tool.
Key takeaways:
- Track realignment in Whitney typically runs $95 to $220 per side, depending on whether the track is bent, the brackets are loose, or the whole door has shifted in the opening.
- Most alignment issues come from impact (a car, a bike, a garbage can) or from loose lag bolts working free over years of heat cycling.
- We photograph the misaligned section before quoting, per Clause 4 of The Haven Standard.
- Straightening a badly bent track is often a stopgap – if the steel is kinked, replacement is the honest answer, and we’ll tell you so.
When You Need Track Realignment
Whitney sits in a stretch of the Las Vegas Valley where summer afternoons push past 110°F and the garage is the hottest room on the property. That heat matters here: steel tracks expand, the lag bolts holding the brackets to the jamb work loose, and a door that ran clean in April can start dragging by August. Here’s what actually signals a realignment problem rather than a spring or opener issue.
- The door scrapes or grinds on one side. A rhythmic metal-on-metal sound that repeats at the same point in the travel usually means the track has bowed inward and a roller is riding the edge. If it’s the right track, check whether a car mirror has clipped it – that’s the single most common cause we see on Whitney Ranch driveways.
- A visible gap between the door and the jamb. Stand inside the garage and look at the vertical gap on each side. One side wider at the top than the bottom means the track is out of plumb, not that the door is crooked.
- The door binds and reverses partway down. If your Genie or Chamberlain opener reverses before the door reaches the floor, the safety sensor isn’t always the culprit. A track that’s pinched at the curve will trip the opener’s force limit and send the door back up.
- Loose brackets you can wiggle by hand. Grab a track bracket (door down, opener off) and try to move it. Any play at all means the lag bolts have backed out of the framing, and the track is walking out of alignment a little more each day.
- A door that’s been hit. Backed into it with the SUV, caught it with a ladder, or had a kid ram a bike into it – impact damage almost always bends the track even when the panels look fine.
- Rollers popping out of the track. When a roller jumps the channel, the door drops and jams. That’s a realignment plus a roller inspection, and it’s worth stopping before it happens again.
If any of those sound familiar, the door is telling you something specific. A technician who photographs the bowed section and shows you the measurement is doing it right – that’s Clause 4, and it’s why we carry a phone on every call.
Our Track Realignment Process

Realignment is a physical job done by hand, and the order matters. Here’s how we work through it, from the moment we pull up to the moment you get the photo record.
- Disconnect the opener and secure the door. We pull the emergency release and, where the door is under tension, clamp the tracks or block the door so it can’t drop while we’re working. A garage door under spring tension is genuinely dangerous to work around, and we don’t take chances with it – the springs and cables stay untouched unless a separate repair calls for them.
- Measure plumb and level at four points. We check each vertical track against a level, then check the horizontal tracks for parallel run. We note the exact gap at top and bottom on both sides, so the “before” number is on paper.
- Photograph the misaligned section. Bent track, backed-out lag bolts, kinked curve – whatever we find, you see the photo before we quote a fix. No description of “bad shape,” just the picture and the measurement.
- Straighten or reset the track. Loose brackets get re-set into fresh framing or anchored with new lags. A slightly bowed track gets worked back with a track bender, not a hammer – hammering a track flattens the channel and ruins the roller race. If the steel is kinked, we tell you it needs replacing instead, and you decide.
- Re-seat the rollers and test the full travel. We set every roller back in its channel, run the door by hand through the full open-close cycle, then re-engage the opener and watch it under power. Balance and force settings get checked on the opener panel.
- Hand you the documented record. You get the photos, the written scope, and the flat price you agreed to before work started. If something’s still not right inside 365 days, the Done Right Promise means we come back and make it right.
Brands matter a little here. Clopay and Amarr doors tend to run heavier panels, so a bent track on those carries more load and needs a firmer fix. Wayne Dalton doors with their proprietary hardware sometimes need a specific roller before a track will run clean. We service all of them, and we’ll tell you which parts we’re using.
Before
AfterTrack Realignment Pricing in Whitney
Track realignment in Whitney typically costs $95 to $220 per side. A single loose bracket and a track that needs a nudge is at the low end; a fully bowed track with bent brackets and replacement rollers is at the top. You get the number in writing before we start, because “call for a quote” isn’t how this works.
| Item | Typical range in Whitney |
|---|---|
| Single track alignment (loose bracket, minor bow) | $95 – $140 |
| Both vertical tracks realigned | $150 – $220 |
| Horizontal track realignment | $110 – $180 |
| Track replacement (kinked steel, per side) | $180 – $320 |
| Roller replacement (set of 10) | $90 – $160 |
| Re-set brackets into framing | $60 – $120 |
What moves the price: whether the track is bent or just out of plumb, how many brackets have pulled out, whether the framing behind them is sound, and whether the door has taken impact damage that also shifted the panels. A door that’s been hit hard enough to bend the track usually needs the panels checked too, and we quote that as a separate line so you can see exactly what you’re paying for.
Estimates are free. Bring us a written estimate from any other company and we’ll give you a free second opinion on it – no coupon, no code, just the paperwork.
FAQs – Track Realignment

How much does track realignment cost in Whitney?
Track realignment in Whitney runs $95 to $220 per side, and a full two-side realignment with fresh brackets is usually $150 to $220. If the track is kinked rather than bowed, replacement adds $180 to $320 per side. Call (888) 402-1096 for an exact quote – estimates are free and the price is written before we start.
Can you realign a track the same day?
Yes – most track realignment jobs in Whitney are done same day, often within a couple of hours. We answer the phone live 24/7, and an emergency call gets a real person, a named technician, and an on-the-way text rather than a callback window.
Is it cheaper to repair or replace a bent track?
Repair is cheaper when the track is bowed or out of plumb; replacement is the honest answer when the steel is kinked or crushed at the curve. Straightening a kinked track weakens it and the roller will jump again within a season. We photograph the bend and tell you which case you’re in before quoting.
Do I need a new garage door if the track is out of alignment?
No. A misaligned track almost never means the door itself is bad. It means the brackets worked loose or the track took a knock, and the fix is re-setting the steel. We’ll only recommend a door replacement if the panels or sections are structurally damaged, and we’ll show you why.
If your door is scraping, binding, or hanging on one side, that’s a track problem and it’s worth stopping before it takes the opener or the rollers with it. Call (888) 402-1096 for a free estimate – a live person answers any hour, we quote a flat written price before any work starts, and you’ll have a photo record in your hand when we leave. For the full scope of what we handle, see our Garage Door Repair in Whitney page, and for everything else we do, start at home.
Written by the team at Servo Garage Doors Whitney, serving Whitney.